The NE is an integrated circuit for processing of signals, such as in the transmission of radio The IC belongs to a family of the following ICs: NE, SA, NE and SA It is widely used in amateur radio applications, i.e. in the. 7 Nov DESCRIPTION. The SAA is a low-power VHF monolithic double-balanced mixer with input amplifier, on-board oscillator, and voltage. 2 Dec INTRODUCTION. For the designer of low power RF systems, the Philips Semiconductors NE mixer/os- cillator provides mixer operation.

Author: Arashijinn Goltizragore
Country: Pakistan
Language: English (Spanish)
Genre: Relationship
Published (Last): 21 September 2008
Pages: 469
PDF File Size: 6.79 Mb
ePub File Size: 19.55 Mb
ISBN: 381-2-11917-408-2
Downloads: 77599
Price: Free* [*Free Regsitration Required]
Uploader: Baran

The power supply should be from 9 to 15V and must be well filtered because of the high audio gain. The 78L05 and red LED provide a regulated supply of about 7V, below the NE’s 8V maximum and nd602 that pins 4 and 5 are biased to approximately half of the supply voltage.

But that’s by no means certain. Using the links people have provided and the mass of PDFs I have downloaded which I have been reading through I feel I have a much better understanding about where to start now. Some successful QRP rigs just drive them from 50 ohms single ended, as atmospheric noise tends to predominate at HF anyway.

Ne6602 again for your assistance, Kerr. As shown in Fig 1, the input circuit is untuned on the presumption that with a double balanced mixer, strong even-harmonic signals will be nd602.

I do have a few random ones I picked up from an amateur radio car boot sale but other than the colour I do not know anything about them yet I got them as they were quite cheap – I may test these as well once N602 get going. I have chosen to use ohms but Jean-Matthieu calculations suggest ohms?

Have a look at this link. This is followed by an emitter-follower to drive headphones to ample volume. Hi Mike, Thanks for your help. Hi Norberto, Thanks for the link you provided, it is very helpful. Nic Hamilton, G4TXG, has underlined that considerable care needs to be taken in the design and construction of direct-conversion receivers to obtain a performance, on the higher frequency bands, truly rivalling that from a well-designed superhet ‘Improving direct conversion receiver design’ RadCom, Aprilpp Subject of the new topic: On Sun, Dec 3, at The local oscillator uses the Colpitts arrangement tuning from about 3.


Using The NE : Joseph J. Carr : Free Download, Borrow, and Streaming : Internet Archive

The NE provides a gain of the order of 18dB with a balanced output across pins 4 and 5 which is amplified by a differential audio amplifier op-amp with a voltage gain of up to Jeffrey Harrison notes that he602 these circumstances a single or, preferably, double tuned circuit should be connected across the input to the IC pins 1,2 see for example the receiver input shown later, in the TT item on the 3. This blog posts suggests that for all parts currently available, the ‘s are the same as the ‘s.

Page 6 shows that when driven single ended at 10mhz, the input impedance is around 5k Page 9 reminds us that when driving the mixer differentially, that input impedance is doubled to 10k.

Are you sure you wish to delete this message from the message archives of BITX20 groups.

AM Radio Receiver Using the NE Balanced Mixer”

This is particularly true in connection with keeping the local oscillator under control and reducing the nw602 of LO leakage, AM breakthrough, hum pick-up and microphony. However in the absence of an ATU to provide the line and act as a band-pass filter strong signals on odd harmonic frequencies could prove troublesome. For a stable fixed-channel stand-by receiver a crystal could be substituted for the tuned circuit.


Thanks again for the link, its theory information is very helpful. During my search for information I also found a very useful page one of ne60 that could be of help to to others: Since this is a later document than AN and is specific to the currently available SAA, seems more likely to be correct with regard to the input impedance. Page 4 of the datasheet: The story conflicts a bit with AN page 3 in that it claims the upgraded part was called thenot the A.

Reason Report to Moderators I think this message isn’t appropriate for our Group. This cannot be undone. Your email is included with the abuse report.

Using The NE602

Have a look at this link http: Pins 6 and 7 of the NE provide connections to the base and emitter of an internally biased transistor. From all I have read I think I need to get a rough starting point and then go from there on a more or less trial and error basis until I get the results I need.

With the high audio gain, the leads in the audio amplifier, including those to the gain control, should be kept as short as possible in order to prevent oscillation. The Group moderators are responsible for maintaining their community and can address these issues. Never says anything about the A variants, though that transition happened aroundlong before this was written. A 50S2 input ne6602 stepped up to match the IC input by a nr602 transformer 2 turns primary, 10 turns secondary wound on toroid balun core.

The new topic will begin with this message. The 47nF capacitor across the NE output provides a crude low-pass filter a sharper, narrower filter would be preferably for CW reception.

However, on the lower frequencies such me602 the 3.

Posted in Art