ISO 11992-4 PDF

ISO is a CAN based vehicle bus standard by the heavy duty truck industry. It is used for ISO Part 4: Diagnostic communication. Reference number. ISO/FDIS (E). STANDARD. ISO/FDIS. DRAFT. RECIPIENTS OF THIS DRAFT ARE INVITED TO. ISO. First edition. Road vehicles — Interchange of digital information on electrical connections between towing and towed vehicles —.

Author: Didal Grojora
Country: Bulgaria
Language: English (Spanish)
Genre: Love
Published (Last): 23 October 2007
Pages: 372
PDF File Size: 6.90 Mb
ePub File Size: 9.9 Mb
ISBN: 267-6-45264-753-5
Downloads: 52056
Price: Free* [*Free Regsitration Required]
Uploader: Meztile

We have no amendments or corrections for this standard.

Missing calibration This sub type is used by the server to indicate, that an operational range etc. Data link layer Layer 1: In downloading this file, parties accept therein the responsibility of not infringing Adobe’s licensing policy.

Unused bytes may have any value. For the diagnostic communication between road vehicles and their towed vehicles the MTYPE parameter shall be coded by means of diagnostic communication channels see Value of signal protection calculation incorrect This sub type is used by the server to indicate that a message was processed with an incorrect protection checksum calculation. Session layer primitives are one to one mapped on transport layer primitives and vice versa without any further action.

Server states while processing a diagnostic service shall be as specified in Table 4, events resulting in a server state change shall be as specified in Table 5.

ISO – Wikipedia

Temperature control cooler, heater, Circuit resistance out of range 1E16 This sub type is used for failures, where the server measures a resistance outside the expected range but not identified as too high or too low. Component or system operation obstructed or blocked This sub type is used for failures where the server has detected that the operation of a component is prevented by an obstruction, e. Signal frequency too low This sub type is used for failures where the server detects excessive duration for one cycle of the output across a specified sample size.

  ARTRITE GOTOSA FISIOTERAPIA PDF

This parameter is only present if DTC information is available to be reported. This part of ISO is applicable to road vehicles of a maximum authorized total mass greater than 3 kg. Signal rate of change above threshold This sub type is used for failures where the signal transitions more quickly than is reasonably allowed. Signal compare failure This sub type is used for failures where the server compares two or more input parameters for plausibility.

The DTC failure type information represents the type of fault in a specific circuit or system. Signal stuck high This sub type is used for failures where the server measures a signal that remains high when transitions are expected. Server state after the diagnostic service has been executed. Your Alert Profile lists the documents that will be monitored. This standard is not included in any packages.

Figure 3 — Client service state diagram — Service request with physical server target address 2? Application layer for brakes and running gear Part 3: CheckImmediately This value indicates that the failure requires an immediate check of the vehicle.

It is the responsibility of the manufacturer to secure a server against unauthorized access and to guarantee performance and safe operation in all operation modes allowing enhanced diagnostics.

  KABADDI GROUND MEASUREMENT PDF

Circuit resistance above threshold 1B16 This sub type is used for failures, where the server infers a circuit resistance above a specified range. It is used for communication between the tractor and one or more trailers. NOTE The functionality for segmenting and reassembling 119992-4 data records is provided by the network layer entities.

ISO standards by standard number. Mechanical Failures This sub type is used for Mechanical Failures that cannot be assigned to a specific sub type. Following a service request with a functional server target address: Articles lacking sources from February All articles lacking sources All stub articles.

ISO 11992-4:2005

ISO consists of the following parts, under the general title Road vehicles — Interchange of digital information on electrical connections between towing and towed vehicles: You can help Wikipedia by expanding it. NOTE For the diagnostic communication, the network layer protocol is used even if less than 8 bytes are transmitted SingleFrame transmission. The service execution has completed successfully.

Confirmation For a diagnostic service response transmitted from a towed vehicle to a towing vehicle, the address parameters of the service primitives 11992- the is meaning: Incorrect has too many pulses 3A16 3B16 — 3F16 — This sub type lso used for failures where the server measures too many pulses e. Signal stuck low This sub type is used for failures where the server measures a signal that remains low when transitions are expected.