FX1N HARDWARE MANUAL PDF

and wiring for Japanese specification FX1N PLC main units. This manual covers basic hardware details for the FX1N Series Programmable Logic Controller. FX1N Hardware Manual – 三菱可编程控制器FX1N型PLC硬件手册. User’s Manual. (Data Communication). FX1S/FX1N/FX2N(C)/FX3U. Interface Modules. INDUSTRIAL AUTOMATION. MITSUBISHI ELECTRIC. MITSUBISHI.

Author: Vorisar Faell
Country: Guinea
Language: English (Spanish)
Genre: Politics
Published (Last): 2 May 2018
Pages: 78
PDF File Size: 20.33 Mb
ePub File Size: 4.68 Mb
ISBN: 866-3-92401-708-1
Downloads: 95140
Price: Free* [*Free Regsitration Required]
Uploader: Zolomuro

During this testing stage take extreme care not to touch any live or hazardous parts. Grounding is recommended but if a proper ground cannot be provided, the PLC will still operate correctly without being grounded.

Mitsubishi FX1NMT-ESS/UL Manuals

When using a DC powered unit, the input circuit power supply should be used. Upper pot, D read from VR1.

The operators should also be familiar with documentation which is connected with the actual operation of the completed equipment. Do not use this terminal Fuse Surge absorbing Diode. Harcware any of the following symbols are encountered, its associated note must be read and understood.

A standard input X0 to X17 defined by the system parameters. C M3 screw to secure top cover.

Please note that the over current induced by in-rush greatly reduces the relay contacts service life. D Top cover for board. The FX1N does not have battery backup, if a system requires backup of more than 10 days, a peripheral backup power source must be provided. Parallel LED Eqn 1: If during the installation of these products or associated products concern is felt, please contact a professional electrician who is trained to the local and national standards applicable to the installation site.

  ALEJANDRO CASONA RETABLO JOVIAL PDF

Mitsubishi FX1N-24MT-ESS/UL Manuals

Fix board to base unit using screws C. Mechanical interlocks MUST be fitted to all safety critical circuits. Features table 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 Top cover Direct mounting holes 4.

AC, World spec, CE registered. This manual provides information for the installation and use manuap the FX1N. E C A Special function or optional equipment board.

Remove base unit top cover. All examples and diagrams shown in this manual are intended only as an hardwarf to understanding the text, not to guarantee operation. See equation 1 for Rb calculation. If resistance Rp is less than the stated value, then add Rb. This includes being completely familiar with all associated documentation for the said product.

FX0N series extension units do not have CE certification. Each of the symbols used will now be listed with a brief description of its meaning. Screw terminals must be secured to prevent a loose connection from causing a malfunction.

FX1N Hardware Manual_图文_百度文库

All maintenance should be carried out in accordance with established safety practices. PL E xtension block? Circuit protector or fuse? If a response haardware of 0. Owing to the very great variety in possible application of this equipment, you must satisfy yourself as to its suitability for your specific application. Do not run input signals in the same multicore cable as output signals or allow them to share the same wire.

  ON4UN LOW BAND DXING PDF

Mitsubishi FX1N-24MT-DSS Manuals

Terminals screws should be tightened to between 0. Under no circumstances will Mitsubishi Electric be liable or responsible for any consequential damage that may arise as a result of the installation or use of this equipment. Terminal layouts The following selection of terminal layouts are taken from the FX1N product range.

If the current leakage is greater than the stated value, then add Rb. D, D M Program execution error ref. To release, pull the spring loaded clips away from the rail and slide the unit up and off. Plug board A into connector B. The value depends on the switch setting. The following instructions are also not suitable. D, D M ref.

Never mount them to the floor or ceiling of an enclosure.

Circuit protector or Fuse? These engineers should also be trained in the use and maintenance of the completed product.