EEPROM 95160 PDF

STMicroelectronics MW Series EEPROM are available at Mouser Electronics. Mouser offers inventory, pricing, & datasheets for STMicroelectronics . Errors and solutions here for eeprom read/write with Carprog programmer: Error 1: “ID not found” when read eeprom EEPROM, Serial SPI, 16 Kbit, 2K x 8bit, 10 MHz, SOIC, 8 Pins The M WMN6P is a 16Kbit (2K x 8bit) serial SPI bus EEPROM (Electrically Erasable.

Author: Nakora Samuzilkree
Country: Mauritius
Language: English (Spanish)
Genre: Automotive
Published (Last): 6 September 2018
Pages: 38
PDF File Size: 1.50 Mb
ePub File Size: 4.4 Mb
ISBN: 533-3-14870-337-1
Downloads: 59082
Price: Free* [*Free Regsitration Required]
Uploader: Gokasa

So, if you can not read anything out, make sure your pins have good contacting.

MCUmall EPROM BIOS Chip Burner Forum – 8pin

Reply 6 benaknoun Spain Posts. Eepfom 12 ZLM Posts. The “Device blank check failed ” means the chip is not a blank chip, there are some data in the chip. What is your chip on board? Reply 2 benaknoun Spain Posts. Reply 4 benaknoun Spain Posts. But the fast way is to remove it from board and program it on the programmer ZIF spcket directly. Reply 8 benaknoun Spain Posts. It is SOIC8 mil chip. Also, when i click on ID, it says “function not supported on this device” Image Insert: What is your another adapter part number?

  GEORGE BRIDGEMAN CONSTRUCTIVE ANATOMY PDF

When you uploading the image, only use letter and number as file name. What is exact part number? Hi, i have connected the tool to the chip and adapter to the programmer.

Reply 9 ZLM Posts. Device blank check failed at address: Reply 13 benaknoun Spain Posts. The wire can be any wires, as long as you can solder it. Use ToolA instead, because your chip pins already damaged. You need to find a way to test the data. Once 59160 chip is blank, then you can load your data file and click on Write button to wrtie the data into chip.

The only way to test data is: That is safe and fastest way. Reply 11 benaknoun Spain Posts. Reply 3 ZLM Posts. It should be able to open it by eeprrom software. Then the ADP should be used. All other pins are pin to pin connect to programmer socket. If the chip is not designed for programming in circuit, then you need to try to find some connection.

Reply 15 ZLM Posts. Reply 17 ZLM Posts.

Reply 7 ZLM Posts. Reply 19 ZLM Posts. Hi, thanks for your reply, here are the numbers on the chip: Reply 16 benaknoun Spain Posts. To be honest though, the other adapter i bought, not sure what its for??

  COMPENDIUM MALEFICARUM FREE PDF

Carprog 9.31 reads/writes eeprom 95160 with A4/A6 adapter

Reply 18 benaknoun Spain Posts. Hi, it seems i’m doing something right then! I think it should be SOIC8 mil chip. That is depending on your ewprom design. Reply 5 ZLM Posts. Hi, ok forget this chip, its damaged I believe they will do the job.

Most of used on-board chips should have something.

Try to power up the board and do not connect pin 8 Vcc pin. Which part number you selected in software? Reprom 10 benaknoun Spain Posts. Hi, i have received the tools i bought from mcumall canada, there are numbers on the adapters, how do i know which pin is the right matching one with the chip?

You can save data as. Reply 1 ZLM Posts.

Reply 14 benaknoun Spain Posts. Chip is blank does this mean this chip is empty??? If it is “”, then it has no ID on this chip. Also, another question please about the same chip: