INFORMATION, AND RECOMMENDATIONS IN THIS MANUAL ARE BELIEVED TO BE . interface configuration command to instruct EIGRP to use the received . Therefore, to connect disparate EIGRP sites, you must configure the neighbor command with LISP encapsulation on every CE in the network. Cisco Nexus Series NX-OS Unicast Routing Configuration Guide, .. The { ip | ipv6} passive-interface eigrp command suppresses neighbors from forming.

Author: Kizragore Nemuro
Country: Uruguay
Language: English (Spanish)
Genre: Art
Published (Last): 27 August 2016
Pages: 231
PDF File Size: 11.19 Mb
ePub File Size: 14.57 Mb
ISBN: 566-8-87677-974-9
Downloads: 4468
Price: Free* [*Free Regsitration Required]
Uploader: Akimi

Creates an incoming global distribute list that refers to access control list ACL 1. The subnet has one successor, which has an FD feasible distance of Houston config-keychain-key exit Returns to global configuration mode. See All Related Articles.

EIGRP configuration

Houston config-router key chain eddie. Austin config-keychain-key exit Returns to global configuration mode. NOTE With the maximum-paths router configuration command, up to 32 equal-cost entries can be in the routing table for the same destination.

You can use the show ipv6 protocols command to list all EIGRPv6-enabled interfaces including passive interfaces. Houston config-keychain-key send-lifetime Creates a standard ACL number 30 and explicitly permits the Please keep in mind that even if only one of the two routers has a passive interface, the neighbor relationship will fail.

If the parameters do match, the two routers become neighbors and each router adds the other to its EIGRPv6 neighbor table, as listed with the show ipv6 eigrp neighbors command. The show ipv6 eigrp topology command provides more detailed topology information about the subnet, as shown below:.


Houston config-if ip authentication mode eigrp md5. Enable IPv6 routing using ipv6 unicast-routing command. Austin config-router key chain susannah.

Sample Chapter is provided courtesy of Cisco Press. About Affiliates Cisco Systems, Inc. Houston config-router network It can be applied to external type 2 and external type 1 routes but not to intra-area and interarea routes.

Austin config-keychain key 1 Identifies the key number. Austin config-router eigrp log-neighbor-changes Changes with neighbors will be displayed.

13-4 EIGRP for IPv6

R1 configure terminal Enter configuration commands, one per line. Houston config-router no auto-summary Disables auto-summarization. Router config-if ip summary-address eigrp Houston config-keychain key 1 Identifies the key number. The show ipv6 eigrp neighbors command lists each neighbor using link-local IPv6 address along with local interface.

Enables manual summarization for EIGRP autonomous system on this specific interface for the given address and mask. The topology consists of four routers and some of you may have noticed that the topology is the same that we used for multi-area OSPFv3 configuration earlier in the chapter, and also uses identical IPv6 addressing scheme. Austin config-if ip authentication mode eigrp md5.

EIGRP configuration

About Affiliates Cisco Systems, Inc. Austin copy running-config startup-config. Identifies a key chain name, which eigtp match the name configured in interface configuration mode. Houston config-keychain-key key-string tower Identifies the key string. Adds a second line to ACL 30 that explicitly permits the Austin config-keychain-key accept-lifetime Return to Beginning Previous Section. Austin config-router network NOTE Setting the maximum-path to 1 disables load balancing.


EIGRP Configuration With Packet Tracer ⋆

The subnet is reachable via next-hop link-local IPv6 address FE Router config-router passive-interface default. A basic requirement of link-state routing protocols is that routers in an area must have identical LSDBs. The feasibility condition dictates that the reported distance the composite metric reported by a neighbor to reach a subnet is better lower than the currently best metric successor metric to reach the same subnet. One of the most common problems associated with EIGRPv6 probably is that it is not enabled on an interface.

Houston config-keychain-key accept-lifetime The commands used to set these parameters have to be used in global configuration mode. Houston config-router eigrp log-neighbor-changes. Set interface bandwidth and delay to influence metric calculation confoguration configuration mode.

R1 show ipv6 eigrp topology Houston config-if ip authentication key-chain eigrp eddie. Hanndbook config-router distribute-list 2 out. The Hello messages enable routers to discover each other and also contain some parameters. Austin config-if ip authentication key-chain eigrp susannah. Creates a standard ACL configkration 10 and explicitly denies the An administrative distance of 75 is assigned to this summary route. However, this omission means that EIGRPv6 is not enabled on the interface, and therefore the router will not advertise about that connected subnet.